Wood
I also have a picture with the new guide post installed.
Wednesday, August 25, 2010
Home-milled Wood
In case anyone's curious I have posted pictures of some wood I have cut so far on my bandsaw. I'm hoping to go get some more logs later today.
Wood
I also have a picture with the new guide post installed.
Wood
I also have a picture with the new guide post installed.
Sunday, August 15, 2010
Nicer Photos
Saturday, August 7, 2010
Bandsaw Fence Drift Adjustment
Edit: I have now posted my improved way of drift adjustment here.
When I posted about my homemade bandsaw fence, I neglected to show how I compensate for drift. In order to slightly adjust the angle of the fence to the table I add (or subtract) shims, in this case washers, in between the table and the t-track.
When I posted about my homemade bandsaw fence, I neglected to show how I compensate for drift. In order to slightly adjust the angle of the fence to the table I add (or subtract) shims, in this case washers, in between the table and the t-track.
Thursday, August 5, 2010
Homemade Bandsaw Fence
I made this rip fence for my bandsaw using 5/16" T-slot track (2'), T-bolts (2"), cam clamp, thumbscrew thingies, and T-nuts. The T-track is screwed to the front of the table using existing tapped holes. Edit: Later I posted about how I adjust for blade drift here. The fence has a detachable auxiliary fence (the white part) so at some point I can make a low profile fence, and maybe a high profile fence. The white fence pictured here is about 4" tall. As you can see I use the cam clamp, and a knob to secure the fence. In the future I will replace the knob with another cam because I find that the knob's rotational movement occasionally causes the fence to shift when I am tightening down. The wooden bar on the far end of the table is to support the fence when it is off the table. Later I added the miter slot cut-out to the T-track.
Next I added a brush to the wheel. it is made from a old nylon brush. Everything is epoxied together.
Wednesday, July 21, 2010
Wenzloff Saw Kit Completed
I finally completed the handle for the Wenzloff tenon saw kit. It's bubinga with some coats of Watco's oil/varnish mixture. I am very pleased with the results. Bob Rozaieski made a great video of making a handle for a Wenzloff kit on his podcast. These kits are a great way to buy quality saws at a great price, provided that you are willing to make the handle.
Thursday, July 15, 2010
Man vs. Log
Edit: later I built a better log sled here
With the riser block installed and the bandsaw's height capacity increased to 12", I did what I probably shouldn't: actually use the full capacity. I wanted to take a log and turn it into usable lumber. So I went down to the local log dump and took (stole?) a maple log that was about 3' long and 11" diameter. After I took it home I realized that it was way too heavy to maneuver onto my bandsaw. So I had to cut it in half. The only problem is that since it was too heavy for the bandsaw, I was going to saw it by hand. Did I mention that it is 11" and maple? To add to that, the only saw that was coarse enough is a 12" long saw we use to cut down our Christmas tree with. So after getting shirtless and flexing my muscles for the neighbors, I began to cut. It took a really long time.
Eventually I got to a point where all was cut except for a 4" diameter core section. 
So I bashed it with a rock and broke the core section.
Before I started milling I painted the ends with latex paint to reduce moisture loss through the end grain.
To begin milling lumber, there must be one flat face. This can be achieved by a number of ways. I chose to make a jig that rides in the miter slot and is screwed into the log.
Once the log is split in half, a high resaw fence can be used to make the slabbing cuts. 
Make sure your fence is correctly adjusted for drift. My resaw fence is part of my log sled. The blade I used is Highland Woodworking's Woodtrner's Bandsaw Blade, which is specially designed for cutting green lumber.
After the lumber is cut I weigh it and write the date and weight on the end. Every couple of months I will weigh them again. When the weight stops dropping I will move them inside where I will continue to weigh them. One they stop losing weight inside they can be used for some projects. Right now they are stacked and stickered under my porch with a cinder block on top to try to resist warping.
This was not a total victory over the log however. Even though the log was reduced to slabs, it got in some good hits. While slabbing the second half one of the bearings in the middle pulley (the bottom one in this photo) seized up. 
After ordering some replacements from McMaster, the saw was up and running again. Here are some of the boards I cut:
With the riser block installed and the bandsaw's height capacity increased to 12", I did what I probably shouldn't: actually use the full capacity. I wanted to take a log and turn it into usable lumber. So I went down to the local log dump and took (stole?) a maple log that was about 3' long and 11" diameter. After I took it home I realized that it was way too heavy to maneuver onto my bandsaw. So I had to cut it in half. The only problem is that since it was too heavy for the bandsaw, I was going to saw it by hand. Did I mention that it is 11" and maple? To add to that, the only saw that was coarse enough is a 12" long saw we use to cut down our Christmas tree with. So after getting shirtless and flexing my muscles for the neighbors, I began to cut. It took a really long time.
Eventually I got to a point where all was cut except for a 4" diameter core section. 
So I bashed it with a rock and broke the core section.
Before I started milling I painted the ends with latex paint to reduce moisture loss through the end grain. To begin milling lumber, there must be one flat face. This can be achieved by a number of ways. I chose to make a jig that rides in the miter slot and is screwed into the log.
Once the log is split in half, a high resaw fence can be used to make the slabbing cuts. 
Make sure your fence is correctly adjusted for drift. My resaw fence is part of my log sled. The blade I used is Highland Woodworking's Woodtrner's Bandsaw Blade, which is specially designed for cutting green lumber. After the lumber is cut I weigh it and write the date and weight on the end. Every couple of months I will weigh them again. When the weight stops dropping I will move them inside where I will continue to weigh them. One they stop losing weight inside they can be used for some projects. Right now they are stacked and stickered under my porch with a cinder block on top to try to resist warping.
This was not a total victory over the log however. Even though the log was reduced to slabs, it got in some good hits. While slabbing the second half one of the bearings in the middle pulley (the bottom one in this photo) seized up. 
After ordering some replacements from McMaster, the saw was up and running again. Here are some of the boards I cut:
Saturday, July 10, 2010
Grizzly Riser Block Install
Shortly after I bought my bandsaw I bought and installed a Grizzly riser block. I didn't know if it would fit my saw since my saw is not a grizzly saw.
First impressions were not great as the instructions were crumpled, 
but everything else was packed nicely. 
It didn't really matter since I had already read the instructions online.
To begin installation I stripped down the saw,
and unbolted the bolt that connects the top half to the bottom half of the saw.
Then I dropped in the riser block, after drilling out the paint that was in the bottom holes of the riser block with a 1/4" bit. After this slight modification the block fit very well.
Then I placed the top half back on and slipped in the long bolt supplied with the kit. 
Then I reassembled the saw which included putting in the new blade guard on the left side of the saw. This is well made and fit nicely. The one thing that I knew wouldn't work was the replacement guide post, as the one supplied with the kit was round but the one I needed was a hex shaped post.
Other than that the kit worked very well. 
After this I ordered a blade from Highland Woodworking that is specially designed to cut green wood. Why green wood? Stay tuned.
Video on how to install a riser block:
First impressions were not great as the instructions were crumpled, 
but everything else was packed nicely. 
It didn't really matter since I had already read the instructions online.To begin installation I stripped down the saw,
and unbolted the bolt that connects the top half to the bottom half of the saw.
Then I dropped in the riser block, after drilling out the paint that was in the bottom holes of the riser block with a 1/4" bit. After this slight modification the block fit very well.
Then I placed the top half back on and slipped in the long bolt supplied with the kit. 
Then I reassembled the saw which included putting in the new blade guard on the left side of the saw. This is well made and fit nicely. The one thing that I knew wouldn't work was the replacement guide post, as the one supplied with the kit was round but the one I needed was a hex shaped post.
Other than that the kit worked very well. 
After this I ordered a blade from Highland Woodworking that is specially designed to cut green wood. Why green wood? Stay tuned.Video on how to install a riser block:
Subscribe to:
Posts (Atom)
Posts
